Humanscale M2CW1S M2 Monitor Arm Aluminium (Max Load 9.1 Kg), Polished White

Product Information

Setup is simple. The monitor has an included clamp and grommet mount. Installation is mostly handled with a bundled Allen wrench, though you’ll still need a Philips head screwdriver to attach your monitor to the VESA mount. Most owners will be able to install smaller monitors (24 to 27 inches) alone, but help is recommended for larger displays.

We’re not a fan of the arm’s installation. It has two clamps instead of one unified clamp, which is strange, because the base of the monitor arm is one solid piece. There are roughly a dozen screws to install. And the included cable routing can prove hard to tighten once several cables are held within the routing. The Huanuo HNDS12, like the HNDS6 (below), is a bit fiddly to set up. It has two clamps that need to be adjusted and roughly a dozen screws that need to be installed. The gas springs also require a bit of adjustment to reduce the force provide, at least when used with a 24-inch or 27-inch monitor. Grommet mounts insert into the circular cut-outs found on many desks built and sold for corporate offices. A grommet mount is also a form of clamp, but size of the mechanism is different, and the mount attaches the monitor to the interior of the desk instead of an exterior edge.In today’s fast-paced, agile work environment, there’s no time for discomfort. M10, part of Humanscale’s revolutionary new monitor arm line, instantly improves the comfort, health and productivity of any workspace. Built to hold heavier equipment, it's optional strong triple crossbar allows M10 to hold up to three monitors or 21.8 kg (48 lbs.) – all while maintaining a simple and sleek design. Smoothness of motion: We preferred monitor arms that were firm enough to stay put while we worked but could reposition easily and didn’t require too much force. To conclude, in my opinion, there’s one clear winner when it comes to comparing the best microphone boom arm stands – the RODE PS1. This is due to its all-round quality. Not only is it durable and sturdy, but it also has a full range of motion and has a classy design. Instead of using a gas cylinder to counterbalance the weight of the monitor, the M2 monitor arm uses extension spring technology. Without clunky mechanisms to complicate the design, the M2 offers uncompromising lightweight, long-term durability and an ultra-thin design that complements flat-panel monitors and attachments for a truly flexible workstation. Humanscale M8 Monitor Arm

The monitors range of adjustment is a bit limited compared to the LX. It offers 11.5 inches of height, 75 degrees of tilt, 180 degrees of swivel, and 360 degrees of rotation. However, a somewhat more limited height adjustment is typical in this category due to the size of monitors these stands are expected to carry. It’s natural, given the only slight difference in name, to think the Ergotron HX is merely an uprated version of the Ergotron LX. That’s not the case. This is an entirely different monitor arm which pairs its increased capacity with improved build quality and a more professional look. The monitor’s range of adjustment isn’t much different from other high-end monitor arms. It offers 13.3 inches of vertical adjustment, 80 degrees of tilt, and 360 degrees of swivel and rotation. That’s essentially identical to the less expensive Ergotron LX. The Flo’s operation is smoother, however: I found I could adjust a monitor’s height with a mere nudge.Monitor size limits should be respected as well. It might be possible to attach a 40-inch monitor to an arm meant for a 32-inch monitor. The 40-inch monitor may even come within the arm’s weight limit. A larger monitor will distribute weight differently, however, which could cause an arm’s tension mechanism to fail. How we test monitor arms It provides a good range of adjustment, with 13.2 inches of height and 90 degrees of tilt, swivel, and rotation. The arm’s height and tilt adjustment are comparable to others on this list, but it can’t swivel in a full circle, which may prove annoying if you frequently move a monitor arm to share your screen with colleagues. We’ve all been in a situation where a recording studio or room is littered by cables, trying to figure out which ones are attached to certain microphones or instruments. Thankfully, a lot of desktop stands are pre-fitted with XLR cables. The cable is internally threaded through the stand, which allows you to simply plug in and record. This capability saves a lot of time and clutter and is featured on a select few microphone suspension arms. Final Verdict